Filter
Top Products
6
refer to your phone’s owners manual for
instructions.
6. If pairing is successful, headset exits pairing mode
and is ready for use. The headset LED Indicator Light
will now flash green every few seconds.
7. To manually exit pairing mode, hold the volume
switch up or down for 2 seconds until the LED
Indicator Light stops flashing red/green.
PLEASE NOTE: If pairing does not work, wait 90
seconds, reset your phone or device to the beginning of
the Bluetooth
®
pairing process and repeat steps 1-7.
Once pairing is complete, your headset will work with
your mobile phone any time both units are powered on
and in close proximity to each other.
Pairing Profiles
The BlueVoice™ Headset supports both Hands-Free and
Headset profiles. The headset will automatically select a
profile to use with your paired device. It will first try to
select Hands-Free mode if supported by your phone.
Usually, mobile phones that support both modes will
select Hands-Free mode.
PLEASE NOTE: Hands-Free mode offers added
functionality (see your phone’s owners manual). Pairing
in Hands-Free mode automatically pairs headset in
Headset mode as well.
Master Connection
When the BlueVoice™ Headset is switched on, or the
pairing button is pressed, the headset will try to pair to
the last paired/used device for approximately 5
seconds. Due to the multi-pairing feature, if a
connection failure occurs, the headset will try to connect
to the next most frequently used device on its stored list
of devices. The LED will indicate when connection
succeeds. If the headset cannot find a device with which
to connect, it will go into pairing mode.
SECTION 4: General Operation
Adjusting the Volume
To increase volume, slide volume switch upward for each
higher volume level. To decrease volume, slide volume
switch downward for each lower volume level. There are
eight (8) separate volume levels. During volume
adjustment, you will hear short high tones getting louder
through the earpiece as the volume goes up and softer
as the volume goes down.
Making and Receiving Calls
Once BlueVoice™ is paired with your mobile phone, you
can make and receive calls using the headset as long as
it is turned on and within range of your phone (up to
10m/30 ft.).
1. For Phones Without Voice-Dialing Capability:
To make a call, dial the number using the phone
keypad and speak to your party through the
headset. When using the headset to receive calls,
press the Answer/End button once to answer. To end
a call, press the Answer/End button a second time.
Patented Self-Adjusting Microphone
Microphone sensitivity automatically adjusts for you
when you extend or retract the microphone.
Turning Headset On/Off
To Turn the
Headset On
Press and hold the On/Off
switch for 2 seconds. If the
headset is already paired
to a mobile phone and the
phone is turned on, the
LED Indicator Light will
flash green for 1.5
seconds and then every 5
seconds while on or in
standby mode. If headset
is not paired to a phone, it
will go into pairing mode.
PLEASE NOTE: If your headset was previously paired,
you may need to press the Answer/End button once.
To Turn the Headset Off
Press and hold the On/Off switch for 2 seconds. The LED
Indicator Light will flash green for 1.5 seconds then
power off.
SECTION 3: Pairing Headset to
Your Phone
Before you begin using the headset, you must pair it to
your mobile phone.
To Pair in Headset and/or Hands
Free Mode
1. Activate the Bluetooth
®
function on your mobile
phone or other device. Please refer to your phone’s
owners manual for instructions.
2. To pair, simply power up the headset. Wait until the
LED Indicator Light will flash red/green alternately.
Once switched on, the device remains pairable for 3
minutes.
3. To force the headset into pairing mode, slide and
hold the volume switch up or down for
approximately 7 seconds until the LED Indicator
Light flashes an alternating green and red. Headset
is pairable for 2 minutes when forced into pairing
mode. Make sure the headset and your mobile
phone are close to each other while pairing. When
the headset enters pairing mode, use your
Bluetooth
®
mobile phone to find it.
4. Follow the Bluetooth
®
pairing/set-up instructions
and screen prompts on your phone to pair it with the
headset. Please refer to your phone’s owners
manual or go to www.fellowes.com/bluetooth for
links to popular phone manufacturers’ websites.
5. When prompted, enter the headset pin code: 0000.
If desired, the pin code may be changed. Please
5
Figure 6
Microphone Microphone
Sensitivity Position
Slightly Higher Extended
Slightly Lower Retracted