Filter
Top Products
3. SPECIFICATIONS
Frequency Response 10 Hz to 93 kHz
Noise Level -110 dBu
THD+N @ 1 kHz / 0 dBu < 0,005 %
Input Impedance >250 kOhm
Load Impedance >600 Ohm
Inputs 1/4 jack unbal. In/ Link Out
XLR unbalanced In
Output XLR balanced Out
Maximum Input level +10/+30/+50 dBu
Power supply
Phantom power 18 V DC to 48 V DC
Battery 9 V blockcell 6LR91
Dimensions 150 mm x 130 mm x 60 mm
Weight ca. 650 g
BEHRINGER is constantly striving to maintain the highest professional
standards. As a result of these efforts, modifications may be made from
time to time to existing products without prior notice. Specifications and
appearance may differ from those listed or shown.
2.3 Converting a microphone from high impedance unbalanced to low impedance balanced
Sometimes all thats available (especially when all other mics are in use) is a unbalanced high impedance micro-
phone with an unbalanced jack. With the ULTRA-DI long cable runs to the console can be established without fear of
picking up noise and hum. Just plug the jack into the input and connect the output to the consoles mic in.
2.4 Tapping a signal from a power amplifier output
When no line out is available it is possible to connect an amplifier output directly to the DI100 (for example, recording
direct from a guitar amplifier, TV-speaker, etc). It is possible to connect the output, i.e an extra speaker output, of up to
3000 Watts to the ULTRA-DI without fear of overloading. Pay attention to the two -20 dB buttons on the ULTRA-DI! Both
must be depressed if an amplifier output is connected to the DI100 input.
Fig 2.3: Connection to an amplifier output
+ Always make sure the GROUND LIFT is on (no ground link) when connecting to speaker terminals. This
prevents accidental short-circuiting of the amplifier output. Also make sure the Tip of the input jack is
connected to the red terminal and that the metal housing of the DI100 has no contact with other equipment.
4. WARRANTY
§ 1 WARRANTY CARD/ONLINE REGISTRATION
To be protected by the extended warranty, the buyer must complete and return the enclosed
warranty card within 14 days of the date of purchase to BEHRINGER Spezielle Studiotechnik
GmbH, in accordance with the conditions stipulated in § 3. Failure to return the card in due time
(date as per postmark) will void any extended warranty claims.
Based on the conditions herein, the buyer may also choose to use the online registration option
via the Internet (www.behringer.com or www.behringer.de).
§ 2 WARRANTY
1. BEHRINGER (BEHRINGER Spezielle Studiotechnik GmbH including all BEHRINGER subsidi-
aries listed on the enclosed page, except BEHRINGER Japan) warrants the mechanical and
electronic components of this product to be free of defects in material and workmanship for a
period of one (1) year from the original date of purchase, in accordance with the warranty regula-
tions described below. If the product shows any defects within the specified warranty period that
are not due to normal wear and tear and/or improper handling by the user, BEHRINGER shall, at
its sole discretion, either repair or replace the product.
2. If the warranty claim proves to be justified, the product will be returned to the user freight prepaid.
3. Warranty claims other than those indicated above are expressly excluded.
§ 3 RETURN AUTHORIZATION NUMBER
1. To obtain warranty service, the buyer (or his authorized dealer) must call BEHRINGER (see
enclosed list) during normal business hours BEFORE returning the product. All inquiries must be
accompanied by a description of the problem. BEHRINGER will then issue a return authorization
number.
2. Subsequently, the product must be returned in its original shipping carton, together with the
return authorization number to the address indicated by BEHRINGER.
3. Shipments without freight prepaid will not be accepted.
§ 4 WARRANTY REGULATIONS
1. Warranty services will be furnished only if the product is accompanied by a copy of the original
retail dealers invoice. Any product deemed eligible for repair or replacement by BEHRINGER
under the terms of this warranty will be repaired or replaced within 30 days of receipt of the product
at BEHRINGER.
2. If the product needs to be modified or adapted in order to comply with applicable technical or
safety standards on a national or local level, in any country which is not the country for which the
product was originally developed and manufactured, this modification/adaptation shall not be
considered a defect in materials or workmanship. The warranty does not cover any such modifi-
cation/adaptation, irrespective of whether it was carried out properly or not. Under the terms of this
warranty, BEHRINGER shall not be held responsible for any cost resulting from such a modifica-
tion/adaptation.
3. Free inspections and maintenance/repair work are expressly excluded from this warranty, in par-
ticular, if caused by improper handling of the product by the user.
This also applies to defects caused by normal wear and tear, in particular, of faders, potentiometers,
keys/buttons and similar parts.
4. Damages/defects caused by the following conditions are not covered by this warranty:
s misuse, neglect or failure to operate the unit in compliance with the instructions given in
BEHRINGER user or service manuals.
s connection or operation of the unit in any way that does not comply with the technical or safety
regulations applicable in the country where the product is used.
s damages/defects caused by force majeure or any other condition that is beyond the control of
BEHRINGER.
5. Any repair or opening of the unit carried out by unauthorized personnel (user included) will void the
warranty.
6. If an inspection of the product by BEHRINGER shows that the defect in question is not covered
by the warranty, the inspection costs are payable by the customer.
7. Products which do not meet the terms of this warranty will be repaired exclusively at the buyers
expense. BEHRINGER will inform the buyer of any such circumstance. If the buyer fails to submit a
written repair order within 6 weeks after notification, BEHRINGER will return the unit C.O.D. with a
separate invoice for freight and packing. Such costs will also be invoiced separately when the buyer
has sent in a written repair order.
§ 5 WARRANTY TRANSFERABILITY
This warranty is extended exclusively to the original buyer (customer of retail dealer) and is not
transferable to anyone who may subsequently purchase this product. No other person (retail dealer,
etc.) shall be entitled to give any warranty promise on behalf of BEHRINGER.
§ 6 CLAIM FOR DAMAGES
Failure of BEHRINGER to provide proper warranty service shall not entitle the buyer to claim (conse-
quential) damages. In no event shall the liability of BEHRINGER exceed the invoiced value of the
product.
§ 7 OTHER WARRANTY RIGHTS AND NATIONAL LAW
1. This warranty does not exclude or limit the buyers statutory rights provided by national law, in
particular, any such rights against the seller that arise from a legally effective purchase contract.
2. The warranty regulations mentioned herein are applicable unless they constitute an infringement
of national warranty law.
The information contained in this manual is subject to change without notice. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical,
including photocopying and recording of any kind, for any purpose, without the express written permission of BEHRINGER Spezielle Studiotechnik GmbH.
BEHRINGER and ULTRA-DI are registered trademarks. ALL RIGHTS RESERVED. © 2001 BEHRINGER Spezielle Studiotechnik GmbH.
BEHRINGER Spezielle Studiotechnik GmbH, Hanns-Martin-Schleyer-Str. 36-38, 47877 Willich-Münchheide II, Germany
Tel. +49 (0) 21 54 / 92 06-0, Fax +49 (0) 21 54 / 92 06-30