Audio Analogue SRL Verdi Cento Stereo Amplifier User Manual


 
15
Selezione/Attivazione modalità By-Pass
Questa funzione permette di utilizzare il Verdi Cento come amplificatore finale. Per configurare la modalità By-Pass si deve
selezionare l’ingresso linea dove si andrà a connettere il preamplificatore e attivare la funzione con il telecomando dopo la
riaccensione dell’apparecchio. La procedura per attivare la modalità è la seguente:
- Accendere l’apparecchio mediante il pulsante “POWER” sul pannello frontale.
- Durante la procedura di riscaldamento delle valvole (i led del volume si accendo uno per volta in
sequenza) ruotare la manopola volume in senso orario e contemporaneamente tenere premuto il tasto
SELECT” sul pannello frontale. Mantenere questa condizione per alcuni secondi (5-6), finché non si
accendono i due led che si trovano in alto sopra la manopola del volume ad indicare la modalità del
ByPass Setup come indicato nella immagine seguente.
- Then use the
IN+” and “IN-” switches on the remote to select the input to bypass.
- Once you have selected the input, push “STANDBY AMP” on the remote to activate the Bypass
function with the selected input. The unit then will end the warm up procedure, if necessary, and will
enter the bypass mode showing the two upper volume leds and the Selected Input led turned on.
-
Utilizzare i tasti del telecomando “IN+” e “IN-” per selezionare l’ingresso da bypassare.
- Una volta selezionato l’ingresso desiderato premere il tasto “STANDBY AMP” dal telecomando per
attivare la modalità By-Pass. Se l’apparecchio non ha terminato il Countdown per il riscaldamento delle
valvole, allora rimarrà acceso il led dell’ingresso selezionato e continuerà la procedura di riscaldamento
per poi accendere l’apparecchio in modalità By-Pass con la visualizzazione fissa dei due led che si
trovano in alto sopra la manopola del volume e del led relativo all’ingresso bypassato.
Important Note: if the unit has been set in Bypass mode, when you turn it off the selected bypass input and the
Bypass mode are memorized. When you subsequently turn on the unit, the Bypass mode will be indicated by
the turning on of the upper volume leds, and the selected bypass input will blink. Then you can choose if you
want to use the unit in normal mode or in Bypass mode. To have the Bypass mode functionality push
“STANDBY AMP” on the remote, while to have a Normal function mode (where the unit works like an integrated
amplifier) push “SETUP” on the remote.
Importante: se l’apparecchio è stato configurato in ByPass mode, quando viene spento, l’ingresso selezionato
per il bypass e il settaggio in modalità ByPass vengono memorizzati. Quando successivamente l’apparecchio
viene riacceso, il precedente settaggio in ByPass mode viene indicato accendendo i due led del volume posti
sopra la manopola e facendo lampeggiare il Led dell’ingresso selezionato per il ByPass. A questo punto è
possibile scegliere se utilizzare il Verdi Cento in modalità ByPass o in modalità normale. Per selezionare la
modalità ByPass premere “STANDBY AMP” sul telecomando mentre per selezionare la funzionalità normale
nella quale il Verdi Cento è un amplificatore Integrato premere il tasto “SETUP” sul telecomando.
NOTES:
entering in Bypass mode deletes the balance settings.
If you have entered the By Pass Mode procedure but you don’t want to activate it push the “SETUP” switch on the remote
to come back to normal function mode. In such cases the unit will end the start up procedure if necessary.
If no input is selected during the Bypass mode setting procedure (this means no input led is turned on) pushing both
“SETUP” and “STANDBY AMP” will drive the unit into normal mode functionality. If necessary the unit will end the start up
procedure.