Filter
Top Products
16W @ 70.7V
FAP62TB
Full Range
16W @ 70.7V
FAP62T-UL2043 FAP62T-UL2043 FAP62T-UL2043 FAP62T-UL2043
Full Range
16W @ 70.7V
Full Range
16W @ 70.7V
Full Range
16W @ 70.7V
Full Range
Ceiling Material up to 1-1/4"
Auxiliary Suspension Point
Tile Bridge
Ceiling Material up to 2"
Tile Bridge
Auxiliary Suspension Point
Dogleg In Normal Position
Dogleg In Inverted Position
Tap Wattage Total: 64 Watts
Typical 120 Watt 70.7V Output
Typical Parallel Hookup of Full Range 70.7/100V Speakers
1 2
3 4 5 6 master
power
power
Amplifier
Input
-
+
-
+
-
+
-
+
-
+
FAP62T
Installation Instructions
ATS001131 RevF 12/08
FAP62T
Installation Instructions
Mounting Template
11" Diameter
The Atlas Sound Strategy Series
®
II assembly mounts easily into existing
construction drop ceiling or drywall materials.
Painting Shield
10
1
⁄2" Diameter
Drop Tile Ceiling
Installation
1. Remove 2' x 2' or 2' x 4' tile.
2. Align adjustable dual rail & C-ring assembly on rear of tile in desired position.
3. Using the template provided, mark cut out circle with marker and cut hole.
(11" FAP62T)
4. Affix C-ring assembly to rails using screws provided and position assembly on rear of ceiling tile.
Replace tile into grid. Be sure formed ends of tile bridge rails engage T-bar tile support rails.
5. Bring service loop from rear of tile, through the tile bridge/C-ring to the access panel located on side of enclosure.
Terminate the service loop to Phoenix style connector provided (please note polarity).
Combination knockouts are provided to facilitate conduit.
6. Insert enclosure through front of tile. Using standard #2 Phillips screwdriver or screw-gun, tighten four dogleg assemblies
until they engage the C-ring assembly. DO NOT OVER-TIGHTEN DOGLEG SCREWS!
7. Adjust front mounted switch to desired wattage tap setting or 8Ω* (See important note regarding 8Ω operation)
8. Install press-fit grille into front bezel ring. Push baffle upwards until it is flush with the bezel ring.
9. For safety and seismic considerations a suspension ring is integrated into the input panel section of unit.
Atlas Sound strongly suggests that a support wire be installed from this support point to a suitable anchor point above ceiling grid.
In drop tile applications, this wire can usually be installed from an adjacent tile access near speaker location.
Dry Wall ("Hard Deck") Installation
1. Using the template provided, mark cut out circle in desired mounting location and cut hole. (11" FAP62T)
2. Place tile bridge rails and C-ring through hole. Use V-shaped edge of C-ring to align tile bridge assembly above ceiling
(alignment screws provided are not required for this type of installation)
3. Bring service loop from rear of tile, through the tile bridge / C-ring to access panel located on the side of the enclosure. Terminate service loop to Phoenix style
connector provided (please note polarity). Combination knockouts are provided to facilitate conduit.
4. Insert enclosure into hole. Using standard #2 Phillips screwdriver or screw-gun, tighten four dogleg assemblies until they engage the C-ring assembly.
DO NOT OVER-TIGHTEN DOGLEG SCREWS!
5. Adjust front mounted switch to desired wattage tap setting or 8Ω* (See important note regarding 8Ω operation)
6. Install press-fit grille into front bezel ring. Push baffle upwards until it is flush with the bezel ring.
New Construction (Drywall Ceilings)
Use of optional FAP62-TR
1
(for use with FAP62T) new construction bracket essentially reserves a speaker mounting location prior to drywall installation
in new construction. Bracket mounts between 16" or 24" OC studs and includes a
3
⁄8" downward lip to provide a template for drywall installers to cut
around. For final installation, please follow these instructions:
Note: Tile bridge components are not used in new construction applications where new construction bracket is utilized.
1. Bring service loop through hole in ceiling provided by pre-construction bracket to access panel located on side of the enclosure. Terminate service
loop to Phoenix style connector provided (please note polarity). Combination knockouts are provided to facilitate conduit.
2. Insert speaker assembly into hole. Using standard #2 Phillips screwdriver or screw-gun, tighten four dogleg assemblies until they engage the ring provided
on the new construction bracket. DO NOT OVER-TIGHTEN DOGLEG SCREWS!
3. Adjust front mounted switch to desired wattage tap setting or 8Ω* (See important note regarding 8Ω operation)
4. Install press-fit grille into front bezel ring. Push baffle upwards until it is flush with the bezel ring.
1
FAP62-TR has not been evaluated by UL Laboratories
NOTE: Doglegs will accommodate ceiling material thickness up to 1
1
⁄4" as shipped from factory. For thicker ceiling materials (up to 2") simply unscrew and flip doglegs
as shown. DO NOT OVER-TIGHTEN DOGLEGS IN EITHER CONFIGURATION!
NOTE: UL recognized conduit clamp must be used for conduit connections. Cable connection cavity is not intended to be used as a junction box.
NOTE: *DO NOT USE 8Ω SETTING WITH 70.7V / 100V SYSTEMS! *DO NOT OVERPOWER IN 8Ω CONFIGURATION!
AMPLIFIER OUTPUT SHOULD NOT EXCEED 32 W RMS @ 8Ω PER SPEAKER
FREQUENCY RESPONSE: 90Hz - 20kHz SENSITIVITY: 88dB (1W / 1M)
16W @ 70.7V
F AP62TB
Full Range
16W @ 70.7V
F AP62T-B
Fu ll Range
16W @ 70.7V
F AP62T-B
Full Range
16W @ 70.7V
FAP62T-B
Fu ll Range
16W @ 70.7V
F AP62T-B
Fu ll Range
Ceiling Material up to 1-1/4"
Auxiliary Suspension Point
Tile Bridge
Ceiling Material up to 2"
Tile Bridge
Auxiliary Suspension Point
Dogleg In Normal Position
Dogleg In Inverted Position
Ta p Wattage Total: 64 Watts
Ty pical 120 Watt 70.7V Output
Ty pical Parallel Hookup of Full Range 70.7/100V Speakers
Amplifier
Input
-
+
-
+
-
+
-
+
-
+
16W @ 70.7V
FAP62TB
Full Range
16W @ 70.7V
FAP62T-UL2043 FAP62T-UL2043 FAP62T-UL2043 FAP62T-UL2043
Full Range
16W @ 70.7V
Full Range
16W @ 70.7V
Full Range
16W @ 70.7V
Full Range
Ceiling Material up to 1-1/4"
Auxiliary Suspension Point
Tile Bridge
Ceiling Material up to 2"
Tile Bridge
Auxiliary Suspension Point
Dogleg In Normal Position
Dogleg In Inverted Position
Tap Wattage Total: 64 Watts
Typical 120 Watt 70.7V Output
Typical Parallel Hookup of Full Range 70.7/100V Speakers
1 2
3 4 5 6 master
power
power
Amplifier
Input
-
+
-
+
-
+
-
+
-
+
ATS001131 RevD 5/08