Filter
Top Products
slider is moved or the pitch function has been
turned off. This adjustment can be made with
or without a disc in the drive. The pitch adjust
-
ment will remain even if a disc has been removed
and will reflect on any other disc loaded into the
player. That is to say, if you set a +2% pitch on
one disc, remove that disc and insert another,
that disc too will have a +2% pitch. The amount
of pitch being applied will be displayed in the
LCD (22).
6. TIME MODE - The TIME button will switch the
time value described in the TIME METER
between
ELAPSED PLAYING TIME, TRACK
REMAINING
TIME, and TOTAL REMAINING TIME.
7. (+) PITCH BEND BUTTON - The (+) pitch
bend function creates a momentary “BUMP” in
the CD’s BPM’s (Beats per minute) while it is
playing. This will allow you to match the beats
between two playing CD’s or any other music
source. Remember, this is a momentary function.
When you remove your finger from this button,
the BPM’s will automatically return to PITCH
SLIDERS (5) selected pitch. Holding down this
button will give a maximum of +100% pitch.
(-) PITCH BEND
BUTTON - The (-) pitch
bend function creates a momentary “Slow Down”
in the CD’s BPM’s (Beats per minute) while it is
playing. This will allow you to match the beats
between two playing CD’s or other playing music
source. Remember, this is a momentary function.
When you remove your finger from the pitch but
-
ton, the BPM’s will automatically return to
PITCH
SLIDERS (5)
pitch value. Holding down this but-
ton will give a maximum of -100% pitch. Use
this function to slow to another playing music
source. Be sure to notice that this function is a
momentary pitch adjustment, for a more precise
adjustment use the
PITCH SLIDER (5) to match
the BPM’s with another playing music source.
8. SGL/CTN - This function allows you to choose
between single track play or continuous track
play (all tracks in order). This function also oper
-
ates in
FLIP-FLOP mode.
9. SCRATCH EFFECT BUTTON - This button
is used to activate and deactivate the Scratch
effect.
10. JOG WHEEL/EFFECTS PLATTER - This
wheel has two functions;
A. The jog wheel will act as a frame search con-
trol when the CD is in pause or cue mode,
allowing you to set a cue point.
B. The wheel also works as a pitch bend during
Playback. Turning the wheel clockwise will
increase the pitch percentage up to 100%,
and turning the wheel in the counter-clock-
wise direction will decrease the pitch per-
centage down to
-100%. The pitch bend will
be
determined on how long you turn the jog
wheel continuously.
11. CD LED - This LED will light up when a CD is
loaded and the player is ready for use.
12. EJECT FUNCTION - Pressing this will eject
the CD. The eject function will only when the unit
is in cue mode, this is to prevent accidentally
ejecting the disc when in play mode.
13. MEMORY BUTTON - This button allows you
to program up to three (3) cue points or three (3)
samples in to the three
BANK BUTTONS (3). The
samples or cue point can then be recalled at any
time even when the disc has been removed and
replaced at a later time.
14. PLAY/PAUSE BUTTON - Each press of the
PLAY/PAUSE BUTTON causes the operation to
change from play to pause or from pause to play.
While in play mode the green play LED will glow,
and while in pause mode the green play LED will
flash.
15. SAMPLER BUTTON - This is used to acti-
vate the sampler function. When this function is
activated a created sample will play in a continu
-
ous loop mode.
16. CUE - Pressing the CUE button during play-
back immediately pauses playback and returns
the track to the last set cue point (see setting a
CUE POINT, page 16). The red CUE LED will glow
when the unit is in cue mode The LED will also
flash every time a new CUE POINT is set.
The
CUE button can be held down to momentarily
play the CD. When you release the CUE button it
GENERAL FUNCTIONS AND CONTROLS (Cont.)
©American Audio® - www.AmericanAudio.us - CDI-300™ Instruction Manual Page 10