Aiwa XP-EV500 CD Player User Manual


 
C
Portable CD Player
Operating Instructions
使用說明書
3-252-496-11 (1)
D
XP-EV500/EV600B/EV600D
Sony Corporation ©2003
E
http://www.aiwa.com/
CD player (front)
CD唱機(正面)
CD player (rear/inside)
CD唱機(背面/內部)
Display on the CD player
CD唱機上的顯示器
*The button has a tactile dot.
*此按鈕帶有觸覺點。
A
B
中文(繁體字)
警告
為防火災或觸電危險,請勿將本機暴露於雨中
或潮濕處。
請勿將本機安裝在諸如書櫥或壁櫥等密閉
處。
為防火災,請勿讓報紙、桌布、窗簾等蓋住本
機的通風孔。也勿在本機上點放蠟燭。
為防火災或觸電危險,請勿在本機上擺飾花瓶
等裝滿液體的物體。
注意
用於此產品的光學元件會增加對眼睛的危險。
有些國家對於本產品的電源用電池可能規定有
處置的標準。請洽詢當地有關當局。
注意
‧打開時,有看不見的雷射線
‧請勿凝視射線或直接看光學元件
‧AC電源轉接器之電源線上的鐵芯係抑制
EMC電磁波干擾用,請勿任意移除。
(備註:A C 電源轉接器之電源線的鐵芯為
外接式,需在線上纏繞二圈後加以固定。)
CE標誌的有效性僅限於有法律限制的國家,主
要為EEA(歐洲經濟區)國家。
電源
要使用電池(B)時
此CD唱機僅能使用下列電池:
乾電池
‧LR6(AA)鹼性電池(不附帶)
充電式電池
初次使用充電式電池時,請給電池充電。
Sony NH-7WMAA(XP-EV600B和XP-
EV600D附帶,XP-EV500不附帶)或市售
AA尺寸1.2V DC 700mAh的鎳金屬氫充電
式電池
要裝入電池時
1 打開CD唱機背面的電池室蓋。
2 裝入2節電池,使)對準電池室中的圖示,
然後蓋上蓋子,直至發出「卡嗒」的響
聲。
3 使用充電式電池時,請將附帶的AC電源轉
接器連接到CD唱機的DC IN 4.5V插孔和
AC電源插座,然後按s/OFF/CHARGE,
開始充電。
CD唱機給電池充電。顯示器上的「CHG」
指示燈點亮, 指示段節持續點亮。電
池完全充滿後,「C H G 」和 指示消
失。
完全充滿後如果按s/OFF/CHARGE,
指示段節閃爍,並在顯示器上出現
「Full」。
4 拔下AC電源轉接器。
電池使用壽命*(大約時數)
(在平穩表面上使用此CD唱機時。)
播放時間因CD唱機的使用狀態而異。
E‧A‧S‧S
12
2節Sony鹼性 56 59
電池LR6(SG)
(日本生產)
2節NH-7WMAA 18 19
(充電約3小時**)
* JEITA(日本電子資訊技術工業協會)的標
準測值。
**充電時間因充電式電池的使用狀況而異。
要檢查電池的剩餘電力時
可在顯示器上檢查。
當「 」閃爍時請更換電池。
Lo batt*
*僅當CD唱機被設定為發嗶聲時,嗶聲才會鳴響。
請參閱背面的「要關掉操作才聲時」。
的指示段節粗示剩餘電池電力。其一個
段節並不一定代表電池電力的四分之一。
‧根據使用條件, 的指示段節可能增加或
減少。
使用乾電池須知
請務必取下AC電源轉接器。
‧電池耗盡時,請更換2節新電池。
要使用AC電源轉接器(C)時
1 將附帶的AC電源轉接器連接到AC電源插
座上。
The illustrations below show the model XP-EV600B.
下圖為XP-EV600B型號的圖示。
Remote control (XP-EV600B only)
遙控器(僅XP-EV600B)
Note
Use only the supplied remote control. You cannot operate
this CD player with the remote control supplied with other
CD players.
僅能使用附帶的遙控器。不能用其他CD唱機
附帶的遙控器來操作此CD唱機。
Remote control (XP-EV600D only)
遙控器(僅XP-EV600D)
播放CD
要裝入CD時
1 滑動OPEN,打開蓋子(A)。
2 將CD按在樞軸上,然後蓋上蓋子(D)。
‧此CD唱機可以播放按Compact Disc Digital
Audio(光碟數位聲訊)格式錄音的光碟。
‧此CD唱機可以播放按Compact Disc Digital
Audio(光碟數位聲訊)格式錄音的CD-R/
CD-RW,但是具體是否可以播放可能因光
碟的品質和錄音裝置的條件而異。
‧本產品專用於播放符合光碟( C D) 標準的光
碟。最近,有些唱片公司發行用版權保護技
術編碼的各種音樂光碟。請注意這些光碟中
有些不符合C D 標準,可能不能在本機上播
放。
要操作CD唱機時
按鈕/開關及其功能/操作
1 P-MODE/ (播放模式/反覆)
反覆按下直至在顯示器上顯示所需播放模
式。
無顯示:正常播放
「1」:播放單曲
「SHUF」:隨機播放
「PGM」:PGM(程式)播放
要反覆所選播放模式時,請按住直至出現
」。要取消時,請再次按住直至「
消失。
2 SOUND
用於增強低音得到放大的音響。反覆按
下,選擇
增強低音的效果大於 。*
1
3 r/t(B SKIP/F SKIP)(跳躍/搜尋)
按一次rt,找出當前曲目或下一曲
目的開頭。反覆按rt,找出前一曲
目或下接曲目的開頭。按住rt,快
速倒回或快速前進。
4 ca(播放/暫停)/ENTER(ca)
按下,開始播放。再次按下,暫停播放。
要從第1個曲目開始播放時,請在CD唱機
停止時按下2秒鐘以上。
PGM播放時,按下可輸入所選曲目。
5 s(停止)/OFF/CHARGE(s)
按下,停止播放。
6 HOLD
用於鎖定CD唱機或遙控器上的控制器,以
防無意中按下按鈕。CD唱機上的HOLD僅
對CD唱機有效,遙控器上的HOLD僅對遙
控器有效。
7 VOL+/-
按下(遙控器上為轉動或滑動),可調節
音量。
8 E‧A‧S‧S*
2
可以防止跳音。*
3
當開關被設定為「2」時,
則將比「1」時更加強E‧A‧S‧S功能。帶著
CD唱機行走並欣賞高品質C D 音響時,
請將此開關設為「1 」。進行較艱苦的練習
時,推薦將其設為「2」。
9 DISPLAY(僅XP-EV600D)
按下可檢查CD的剩餘時間和剩餘曲目數。
*
1
利用SOUND功能時如果走音,請降低音量。
*
2
E‧A‧S‧S=Electronic Anti-Shock System(防
衝擊電子系統)
*
3
下列情況下可能會跳音:
-如果CD唱機連續受到超過預定強度的衝擊。
-如果播放不乾淨或擦傷的光碟,或
-使用低質CD-R/CD-RW,或錄音裝置或應
用軟體有問題。
要取出CD時
邊按住樞軸(E)邊取出CD。
(下接背面)
English
WARNING
To prevent fire or shock hazard, do not expose the unit to
rain or moisture.
Do not install the appliance in a confined space, such as
a bookcase or built-in cabinet.
To prevent fire, do not cover the ventilation of the
apparatus with newspapers, tablecloths, curtains, etc. And
don’t place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects filled
with liquids, such as vases, on the apparatus.
CAUTION
The use of optical instruments with this product will
increase eye hazard.
Certain countries may regulate disposal of the battery used
to power this product. Please consult with your local
authority.
CAUTION
INVISIBLE LASER RADIATION WHEN OPEN
DO NOT STARE INTO BEAM OR VIEW DIRECTLY
WITH OPTICAL INSTRUMENT
The validity of the CE marking is restricted to only those
countries where it is legally enforced, mainly in the
countries EEA (European Economic Area).
Power Sources
To use the batteries (B)
Use only the following batteries for your CD player:
Dry batteries
LR6 (size AA) alkaline batteries (not supplied)
Rechargeable batteries
Charge the rechargeable batteries before using them for
the first time.
Sony NH-7WMAA (supplied with XP-EV600B and
XP-EV600D; not supplied with XP-EV500) or
commercially-available size AA Ni-MH rechargeable
batteries of 1.2 V DC, 700 mAh
To insert the batteries
1
Open the battery compartment lid on the rear of your CD
player.
2 Insert two batteries by matching the ) to the diagram
in the battery compartment and close the lid until it
clicks into place.
3 When using the rechargeable batteries, connect the
supplied AC power adaptor to the DC IN 4.5V jack of
your CD player and an AC outlet, then press s/OFF/
CHARGE to start charging.
The CD player charges the batteries. The “CHG”
indicator turns on in the display and the indicator
sections of
light up in succession. When the
batteries are completely charged, the “CHG” and
indicators get turned off.
If you press s/OFF/CHARGE after the charge has
already been completed, the
indicator flashes
and “Full” appears in the display.
4 Disconnect the AC power adaptor.
Battery life* (approx. hours)
(When the CD player is used on a flat and stable place.)
Playing time varies depending on how the CD player is used.
EASS
12
Two Sony alkaline 56 59
batteries LR6 (SG)
(produced in Japan)
Two NH-7WMAA 18 19
(charged for about 3
hours**)
* Measured value by the standard of JEITA (Japan
Electronics and Information Technology Industries
Association).
** Charging time varies depending on how the
rechargeable battery is used.
To check the remaining power of the
batteries
You can check it in the display.
Replace the batteries when “
” flashes.
Lo batt*
* Beep sounds only when the CD player is set to sounds beep.
See “To turn off the operation beep sound” on the reverse
side.
Notes
The indicator sections of roughly shows the
remaining battery power. One section does not always
indicate one-fourth of the battery power.
•Depending on operating conditions, the indicator
sections of
may increase or decrease.
Notes on using the dry batteries
•Be sure to remove the AC power adaptor.
When the batteries are depleted, replace both batteries
with new ones.
To use the AC power adaptor (C)
1 Connect the supplied AC power adaptor to an AC
outlet.
Playing a CD
To insert a CD
1 Slide OPEN to open the lid (A).
2 Fit the CD to the pivot, then close the lid (D).
Notes
This CD player can play discs recorded in the Compact
Disc Digital audio (Audio CD) format.
This CD player can play CD-Rs/CD-RWs recorded in the
Compact Disc Digital Audio (Audio CD) format, but
playback capability may vary depending on the quality of
the disc and the condition of the recording device.
This product is designed to play back discs that conform
to the Compact Disc (CD) standard. Recently, various
music discs encoded with copyright protection
technologies are marketed by some record companies.
Please be aware that among those discs, there are some
that do not conform to the CD standard and may not be
playable by this product.
To operate the CD player
Button/switch and its function/operation
1 P-MODE/ (play mode/repeat)
Press repeatedly until the play mode you want appears
in the display.
No indication: Normal play
“1”: Single play
“SHUF”: Shuffle play
“PGM”: PGM (program) play
To repeat the play mode you selected, press and hold
until “
” appears. To cancel it, press and hold again
until “
” disappears.
2 SOUND
Use to emphasize the bass-boosted sound. Press
repeatedly to select
or .
enhances more than .*
1
3 r/t (B SKIP/F SKIP) (skip/search)
Press r or t once to find the beginning of the
current/next track. Press r or t repeatedly to
find the beginning of the previous/succeeding tracks.
Press and hold r or t to go backward/forward
quickly.
4 ca(play/pause)/ENTER (ca)
Press to start playing. Press again to pause playing.
To play from the first track, press for 2 seconds or
more while the CD player is stopped.
Press to enter the selected track for the PGM play.
5 s(stop)/OFF/CHARGE (s)
Press to stop playing.
6 HOLD
Use to lock the controls on your CD player or remote
control to prevent accidental button presses. HOLD
on the CD player works only for the CD player, while
HOLD on the remote control works only for the
remote contol.
7 VOL+/–
Press (turn or slide for the remote control) to adjust
the volume.
8 EASS*
2
Protect against sound skipping.*
3
When the switch is
set to “2”, the E•A•S•S function will be enhanced
compared to “1”. To walk with the CD player and
enjoy high quality CD sound, set the switch to “1”.
While taking harder exercise, it is recommended that
you set it to “2.”
9 DISPLAY (XP-EV600D only)
Press to check the remaining time on the CD and the
number of tracks let.
*
1
If the sound is distorted when using the SOUND function,
turn down the volume.
*
2
E•A•S•S = Electronic Anti-Shock System
*
3
Sound may skip:
if the CD player receives stronger continuous shock than
expected,
if a dirty or scratched CD is played or
when using poor-quality CD-Rs/CD-RWs or if there is a
problem with the recording device or application software.
To remove the CD
Remove the CD while pressing the pivot (E).
(Continue to the reverse side)
\ (headphones)
jack
(頭戴耳機)插孔
6HOLD
DC IN 4.5 V
(external power
input) jack
DC IN 4.5 V
(外部電源輸入)
插孔
7VOL +*/–
5s(stop)/OFF/
CHARGE
s(停止)/OFF/
CHARGE
Display
顯示器
4e (play/
pause)/ENTER*
e
(播放/暫停)/
ENTER*
3r/t
(skip/search)
r/t
(跳躍/搜尋)
8EASS
Insert the ( end first (for both
batteries).
(2節電池都是)先插入
(端。
Play mode
播放模式
Playing time
播放時間
Remaining battery power
剩餘電池電力
to an AC outlet
至AC電源插座
AC power
adaptor
AC
電源
轉接器
Label side up
標籤面朝上
2SOUND
1P-MODE/
Strap holes
吊帶孔
OPEN
Open the battery
compartment lid.
打開電池室蓋。
Sound mode
聲音模式
CHG
\
Earphones
耳機
DC IN
4.5 V
Track number
曲目號
4e
7VOL
Headphone
jack
頭戴耳機
插孔
3tF SKIP
3rB SKIP
2SOUND
6HOLD
5s
7VOL +/–
Display
顯示器
Headphone
jack
頭戴耳機
插孔
5s 4e
3r/t
Clip
夾子
6HOLD
2SOUND
1P-MODE/
9DISPLAY
03.2.24, 1:57 PM1