Filter
Top Products
4
MODELO 4C523K/9154K
2084020A Rev. F 9/00
11
22
14-
ENSAMBLAJE
(Ilustración para Ensamble - Pagina 1)
1. Alinea la REJILLA TRASERA con el pasador localizado en la TAPA
DE PLASTICO DEL MOTOR. Dejando los dos agujeros del centro asi
abajo.
2. Asiente la REJILLA y sujetela con la TUERCA DE PLÁSTICO.
3. Para evitar lastimar el HELICE, instalela empujando firmemente en el
centro hacia el EJE del MOTOR.
4. Coloque el GANCHO en la REJILLA DELANTERA sobre el alambre
central superior en la REJILLA TRASERA.
5. Torciendo suavemente quitar del sujetador los GANCHOS de la
REJILLA y colocarlos uniformemente alrededor del ventilador. Fijar
los GANCHOS en la REJILLA. Hacer que la cola del gancho agarre un
alambre redondo de la REJILLA TRASERA. Hacer que el cuerpo del
gancho agarre los bordes planos de ambas rejillas.
(Figura a y b
pagina 1)
OPERACIÓN
1. VELOCIDAD: Las velocidades se controlan mediante el conjuntor
rotatorio localizado en la base del ventilador.
2. OSCILACIÓN: Para hacer oscilar el ventilador, oprima el botón que se
encuentra sobre la cubierta del motor. Para que el ventilador deje de
oscilar, tire del botón hacia afuera.
3. AJUSTE DEL ÁNGULO: Se puede cambiar el ángulo del conjunto
superior del ventilador, aflojando primero el tornillo de elevación. Coloque
el conjunto superior en el ángulo deseado y fíjelo en posición volviendo
a apretar el tornillo de elevación.
LISTA DE REPUESTOS
Ref. No. de Parte Descripción Cant.
a) Jalé el boton de oscilacion asi
arriba para desenganchar el
mecanismo de oscilacion.
b) Usé un objecto como un mango
de un destornillador y
gentilmente pegé un golpecito
a la parte delantera de la helice.
No golpear el eje de la helice
asi adentro del motor.
c) Delé vuelta a la helice con la
mano. Si la helice no davuelta
libremente, sigá el paso
posterior hasta que la helice
gire libre.
PRECAUCION: De ninguna
manera prenda su ventilador sin
las revillas y asegurese que
ambas esten bien aseguradas.
TAP
HUB
SPIN
UP
1
2
3
a
b
c
GIRAR
ARRIBA
Centro
EJE
GOLPEAR
LIGERAMENTE
EJE
SPECIFICATIONS
Motor ................................................ 120V, 60 Hz
Blade diameter ................................ 9" (22.9 cm)
Speeds ............................................. 2
Control ............................................. Rotary Switch
Air flow distribution .......................... 90°
Approvals ......................................... UL Listed. Close mesh fan
guard meets OSHA requirements.
R
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
DESCRIPTION
The AirKing 9" (22.9 cm) oscillating fan features whisper-quiet perfor-
mance with a 3-paddle fan blade. The fan has a permanently lubricated
motor with a 6 ft (1.8 m) 18/3 cord set.
1
2084020A
9 INCH OSCILLATING FAN
MODEL 4C523K/9154K
BLADE
MOTOR
PLASTIC
NUT
REAR GRILL
FRONT
GRILL
GRILL CLIP
HOLDER
PLASTIC GRILL
CLIPS
.
HOOK
OSCILLATION CONTROL
ELEVATION
SCREW
SWITCH KNOB
a. b.
OPERATING INSTRUCTIONS & PARTS MANUAL
MODEL 4C523K/9154K
SPEED HIGH LOW
CFM 1205 906
M
3
/s .57 .43
RPM 2175 1644
Amps .55 .32
Watts 32 22
dB A 41 34
GENERAL SAFETY INFORMATION
1. Make certain that the power source conforms to the electrical require-
ments of the fan.
2. The power cord is equipped with a three-prong grounded plug that must
be inserted into a matching receptacle. Under no circumstances must
the grounding prong be cut off the plug. Where a two-prong wall
receptacle is encountered, it must be replaced with a properly grounded
three-prong receptacle installed in accordance with the National Elec-
trical Code (NEC) and all applicable local codes and ordinances. This
work must be done only by a qualified electrician, using copper wire only.
WARNING: USE OF A THREE-PRONG TO TWO-PRONG ADAPTER IS
NOT RECOMMENDED. IMPROPER CONNECTION MAY CREATE
THE RISK OF ELECTROCUTION. USE OF SUCH ADAPTERS IS NOT
PERMITTED IN CANADA.
3. Where possible, avoid the use of extension cords. If they must be used,
minimize the risk of overheating by ensuring that they are UL listed and
of the proper gauge and length. Never use a single extension cord to
operate more than one fan.
4. Do not insert fingers or foreign objects into the fan. Do not block or
tamper with the fan in any manner while it is in operation. Do not touch
the fan while in operation or just after it has been turned off, as some
parts may be hot enough to cause injury.
5. Unplug power cord before installing or servicing the fan.
WARNING: DO NOT DEPEND UPON THE ON-OFF SWITCH AS THE
SOLE MEANS OF DISCONNECTING POWER WHEN INSTALLING OR
SERVICING THE FAN. ALWAYS UNPLUG THE POWER CORD.
6. This fan is intended for general use ONLY. It must NOT be used in
potentially dangerous locations such as flammable, explosive, chemi-
cal-laden or wet atmospheres.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT USE THIS FAN WITH ANY SOLID STATE SPEED CONTROL
DEVICE.
7. Be sure fan is on a stable surface when operating, to avoid chance of it
overturning.
8. DO NOT use fan in a window. Rain may create an electrical hazard.
9. Completely reassemble fan, according to instructions before reconnect-
ing to power supply.
MAINTENANCE
WARNING: ALWAYS UNPLUG THE CORD BEFORE SERVICING.
CLEANING: Use a soft cloth and a mild soap solution such as liquid dish
washing detergent.
CAUTION: Do not use gasoline, benzine, thinner, harsh cleaners,
etc. which will damage the fan.
Dry all parts with a soft cloth completely before reconnecting to power
supply.
STORAGE: When not in use, keep unit in a clean dry place.
MOTOR IS PERMANENTLY LUBRICATED.
Rev. F 9/00
1 2050009AW Cordón Eléctrico 1
2 2096045 Rejilla Delantera 1
3 2010004 Hélice 1
4 2010350 Tuerca de Plástico 1
5 2096050 Rejilla Trasera 1
6 2030056G Motor 1
7 2010619 Cubierta del Motor 1
8 2010119 Botón de Oscilación 1
10 2010279 Enlace 1
11 2090068 Tornillo #6 x 1/2" LH/H.W.H. 1
12 2010260 Cuello 1
13 2091133 Tuerca Hexagonal de 1/4 x 20 1
14 2090529 Tuerca Para Alambre 1
15 2090199 Tornillo Phillips de 1/4 - 20 x 1"
PPH Tornillo de Elevación 1
16 2010104 Botón del Interruptor 1
17 2065412 Ornamento de la Base 1
18 2010524 Base 1
19 2057065 Conjuntor Rotatorio 1
20 2010281 Placa Inferior 1
21 2010403A Pata de Caucho (4 utilizadas) 4
22 2090038 Tornillo Phillips de Cabeza
Reforzada #8 x 9/16 PPH 2
23 2010354 Sujetador de Rejilla 5
24 2066506G Accesorio del Botón del
Interruptor 1
25 2010241A Ornamento del Rejilla 1
26 2070024G Ojo de Buey (AirKing) 1
27 2090073 Tornillo #6 x 1/2" AB 1
27