Filter
Top Products
| ADCOM GTP-880 Owner’s Manual26
27ADCOM GTP-880 Owner’s Manual |
[
40
]
Main Menu Button
In main mode, this is pre programmed to enter on screen
menu of the GTP-880.
[
41
]
Navigation & Select Buttons
The arrow buttons allow navigation throughout the GTP-
880 OSD (ON Screen Display) menus (as well as the menus
of other devices, once the commands are learned).
Select button: In main mode, this is pre programmed to
enter a selection chosen via the menu system.
[
42
]
Pause Button
In CD and DVD mode, it is pre programmed for pause with
an ADCOM GCD-750 and GDV-850.
[
43
]
Stop Button
In CD and DVD mode, it is pre programmed for stop with
an ADCOM GCD-750 and GDV-850.
[
44
]
Direct Access Keypad
In CD mode, buttons are pre programmed as track access
commands for the ADCOM CD player. Buttons “1” through
“10,” and “+10”
In tuner mode these buttons allow direct access to preset
stations in memory.
In DVD mode, buttons work in conjunction with direct
chapter navigation. Use the go to/enter to jump to a
specific chapter or scene.
[
45
]
Surround Mode Buttons
In main mode, these are pre programmed to cycle through
the available surround modes of the GTP-880.
[
46
]
Direct Analog Input Buttons
These buttons switch the analog inputs to one of the ana-
log direct inputs. DVD-Audio, SACD or a 2 channel bypass.
[
47
]
Random & Repeat Buttons
In CD mode, these buttons are pre programmed as
“random” and “repeat” commands for ADCOM CD player.
[
48
]
Ch. Trim & FM/AM Button
In main mode, this button cycles through channels adjust-
ing trim in 1dB steps, -15dB to +10dB. Use the left and
right arrows to make adjustments. In tuner mode this but-
ton switches the tuner between FM and AM frequencies.
[
49
]
Ch. Cal & Memory Button
In main mode, this button cycles through channels
adjusting level in 1dB steps, -15dB to +10dB. Use the left
and right arrows to make adjustments. In tuner mode this
button is used to program radio stations in memory.
[
50
]
Th-Eq & P.Scan Button
In main mode this button turns theater compensation pro-
cessing on and off.
In tuner mode this button scans the AM or FM stations
preset in the tuner’s memory.
[
51
]
Tone & Tune Down Button
In main mode this button cycles between the treble and
bass level control, use the left and right buttons to make
adjustments.
In tuner mode this button adjusts the GTP-880 tuner’s
frequency down.
[
52
]
Bypass & Tune Up Button
In main mode this button turns tone bypass on and off. In
tuner mode this button adjusts the GTP-880 tuner’s
frequency up.
[
53
]
Macro Buttons
These buttons are programmable for use with any source.
[
54
]
Room 2 Button
In any mode, this button is used turn room 2 on and off,
as well as adjust room settings using the buttons.
[
55
]
Backlight Button
No programming capabilities. Button backlights all keys
for eight (8) seconds when pressed.
[
56
]
Dim Button
In main mode, button is pre programmed to dim
GTP-880’s information display.
2.4 Remote Function Table
The tables on the following pages supplement the infor-
mation you’ve just read. Use it to quickly review button
functions. The controller’s capabilities are extensive and
may be somewhat intimidating at first. However, you
will soon find that its logical button arrangement and
programming capabilities will greatly increase your enjoy-
ment as you discover the ease with which you can operate
your entire system from just one remote! Look down the
left-hand column until you see the button you want to
learn about. Then look under main to see if it is pre pro-
grammed for a GTP-880 function, under CD to see what
CD commands are pre programmed, and under tuner to
see all pre programmed tuning functions.