Arcam AVR200 Home Theater System User Manual


 
AVR200
15
English
MODE
CD DVD
ENTER
CD
DVD
5-1
INFO
TAPE
SAT
AV
CR-340
OK
DVD VCR AUX
CD FM AM
T
MODE
P P+
SLEEP TEST
TRIM
CD/DVD
MODE
DYN
MODE
ENTER
CD
DVD
Using the remote control
CR-340 Remote Control
The CR-340 remote control gives access to all functions
available on the front panel, plus some additional functions
only available from the remote. It also has controls to
operate Arcam CD and DVD players.
Source selection buttons
These operate in the same way as the source selection buttons
on the front panel of your AVR200 ampli er.
RDS INFO
Displays Radio Data System (RDS) text information, if available.
Press again for station frequency, and again to show station
information (the default mode).
SLEEP
Switches the ampli er into stand by mode after a preset number
of minutes. Pressing
SLEEP once will set the sleep time to 90
minutes. SLEEP MODE is shown on the display panel.
Each consecutive press of
SLEEP reduces the sleep time by
30 minutes. Sleep mode is cancelled by setting the time to 0
minutes, or by pressing the
POWER or STANDBY button.
TRIM
Allows direct access to trim the centre, rear and subwoofer
speaker outputs. Press
TRIM to cycle between channels and use
the
and
arrows to adjust levels.
MODE
Scrolls through the available surround sound modes (Stereo,
Pro Logic II, etc.). The selection is shown in the display area
for three seconds.
DYNAMIC RANGE
Compresses the dynamic range for low-level listening of Dolby
Digital sources. The dynamic range may be set from 100% (the
default) to 25% (maximum compression) in steps of 25%. The
reduction is shown on the display.
CD/DVD functions
The CD/DVD button toggles the remote control unit into
controlling an Arcam CD or DVD player: this setting is brie y
con rmed by a light at the top of the controller.
VOLUME and MUTE ( )
Press + to increase volume or to decrease the output volume
on the ampli er.
Press
to mute the speaker connections and pre-amp outputs.
Both tape outputs and the headphone socket remain active. In
mute mode the display ashes MUTING.
Mute is disabled either by pressing
again, or by adjusting the
volume. Note that the volume and mute controls have no effect
on the output levels of Arcam CD players.
Cursor pad and OK button
These are used to navigate through the pages in the on screen
display (OSD). See Using the On Screen Display.
TEST
Engages the test signal generator so that the volume for each
channel can be balanced from your listening position. The signal
moves from Front Left to Centre, Front Right, Rear Right, Rear
Left and Subwoofer in a continuous cycle. Note that the test
signal may not be heard through a subwoofer.
See Using the On Screen Display for full instructions on this
feature.
TUNER MODE
Toggles between Preset mode and Tune mode. See Using the
tuner for details.
P/P+
Cycles through preset radio stations, or scans through frequency,
depending on the Tuner mode setting.
Power/Standby
Toggles the ampli er between stand by mode and full power
mode. The power indicator light next to the power button on the
front panel is red when the ampli er is in stand by and green
when powered up.
CD/DVD lights
These indicate the function of the CD/DVD button at the bottom of
the control. They are not related to any function on the AVR200.
The LED only stays on for 15 seconds to conserve battery life. If
neither LED is lit this does not mean that the remote control unit
is not working!
5.1
Selects the multi-channel output from a DVD audio player or
external decoder source connected to the 5.1 channel input.
NOTE: Remember to install the two AAA batteries
supplied before trying to use your remote control!
Do not place anything in front of the display area on the
AVR200 (where the IR receiver is located), or the remote
control may not work.